I am trying to perform recovery of a 10.7 TB RAID 6 volume from a QNAP file server in another Windows 7 machine. I have built the virtual RAID and the scan seemed to be doing just fine and was chugging along for about 1d18h when I first noticed the "time remaining" kept getting longer, but it was consistently counting down. It got to the last block, 99% complete and a minute remaining and then did something weird - it went to 30% complete and like 8 days remaining...but it seemed to chug pretty quickly (w/in 10 minutes) back to 99%, but it's been pretty much stuck at 4 minutes and some seconds remaining for the last 8+ hours. Any thoughts?
I picked RAID6 / Reed-Solomon, but it was a SWAG (I know it's a RAID 6 volume, but not sure which schema they use)
I am using R-Studio 7.6.156433 on a Windows 7 Dual Xeon machine w/ 4GB of memory and a 3ware 9550SX-8 controller.
NOTE: I never saw Partition 1 show up under the virtual RAID in the drive pain as described/shown in step 3 from http://www.r-tt.com/Articles/RAID_Recov ... ndex.shtml
RAID 6 recovery scan seems to hang at 99%
RAID 6 recovery scan seems to hang at 99%
You do not have the required permissions to view the files attached to this post.
Re: RAID 6 recovery scan seems to hang at 99%
Actually, you may stop the scan. It may stop for a some time, and I advise you to save the scan info immediately after stop. 99% is more than enough to find out the data on the disk.
But looks like that something wrong with the RAID parameters.
But looks like that something wrong with the RAID parameters.
Re: RAID 6 recovery scan seems to hang at 99%
Hello SPYDER
have you solved the issue?
Cor
have you solved the issue?
Cor
Robert
Technical Manager @ Recupero Dati RAID FAsTec (Italy)
USEFUL RULES and GUIDELINES
1) What to check BEFORE begin a disk image/clone process [link]
2) Disks that are too slow while imaging/cloning them [link]
3) All my posts on this forum [link]
Technical Manager @ Recupero Dati RAID FAsTec (Italy)
USEFUL RULES and GUIDELINES
1) What to check BEFORE begin a disk image/clone process [link]
2) Disks that are too slow while imaging/cloning them [link]
3) All my posts on this forum [link]
Re: RAID 6 recovery scan seems to hang at 99%
After about 18 hours at 99% it completed successfully. I think the issue could be do to low (4GB) of RAM on the system. I have ordered more because I'm having issues loading the scan data now...
Re: RAID 6 recovery scan seems to hang at 99%
Have you cloned the single original drives?
Read: have you set on the security side your valuable data?
One RAID 6 fails because 3 (not 2) drives are in trouble and you are stressing them so much.
Please find my others posts with best practices on this forum before to proceed.
Read: have you set on the security side your valuable data?
One RAID 6 fails because 3 (not 2) drives are in trouble and you are stressing them so much.
Please find my others posts with best practices on this forum before to proceed.
Robert
Technical Manager @ Recupero Dati RAID FAsTec (Italy)
USEFUL RULES and GUIDELINES
1) What to check BEFORE begin a disk image/clone process [link]
2) Disks that are too slow while imaging/cloning them [link]
3) All my posts on this forum [link]
Technical Manager @ Recupero Dati RAID FAsTec (Italy)
USEFUL RULES and GUIDELINES
1) What to check BEFORE begin a disk image/clone process [link]
2) Disks that are too slow while imaging/cloning them [link]
3) All my posts on this forum [link]