"Skip Files with bad sectors"
"Skip Files with bad sectors"
Hello.
I just installed the eval-version of R-Studio. The disk to recover does have bad sectors. In order to prevent R-Studio to crash, "Skip Files with bad sectors" was selected.
After beeing able to recover many files, the popup "Files with bad sectors" is shown. Now, whatever selection is made (e.g. mark, or Cancel), the recover operation is aborted and the following messages are written to the Log:
"Read disk at position 12345678 failed after 2 attemps. Illegal seek"
After this message, the partially damaged disk does disappear from /dev and R-Studio has to be restarted.
- How can files which are related to bad sectors reliable be excluded from restore-attemps?
- Is there a way to have R-Studio listed all files which are related to bad sectors?
You help is appreciated. Thank you! Moses
I just installed the eval-version of R-Studio. The disk to recover does have bad sectors. In order to prevent R-Studio to crash, "Skip Files with bad sectors" was selected.
After beeing able to recover many files, the popup "Files with bad sectors" is shown. Now, whatever selection is made (e.g. mark, or Cancel), the recover operation is aborted and the following messages are written to the Log:
"Read disk at position 12345678 failed after 2 attemps. Illegal seek"
After this message, the partially damaged disk does disappear from /dev and R-Studio has to be restarted.
- How can files which are related to bad sectors reliable be excluded from restore-attemps?
- Is there a way to have R-Studio listed all files which are related to bad sectors?
You help is appreciated. Thank you! Moses
Re: "Skip Files with bad sectors"
First, go to the Tools -> Settings -> Bad sectors tab and set Default read attempt to 0.
If that doesn't help, there's hardware problems with the disk hardware that crashes the system, and not R-Studio.
Another way is to create a disk image, and try to recovery files from it.
If that doesn't help, there's hardware problems with the disk hardware that crashes the system, and not R-Studio.
Another way is to create a disk image, and try to recovery files from it.
-
- Posts: 220
- Joined: Tue Oct 20, 2015 10:13 am
- Location: Providence, RI USA
- Contact:
Re: "Skip Files with bad sectors"
It's usually best to clone the disk that has the bad sectors first using a tool like ddrescue in linux. Unfortunately any tool that runs in Windows will have limitations with handling bad sectors, it's just a Windows factor. Then run R-Studio against the clone and you're good to go.
Re: "Skip Files with bad sectors"
Thank you Alt! I am trying to follow your advice but after changing the value to 0 and pressing either "OK", "Apply" or "Set for all drives"Alt wrote:First, go to the Tools -> Settings -> Bad sectors tab and set Default read attempt to 0.
If that doesn't help, there's hardware problems with the disk hardware that crashes the system, and not R-Studio.
Another way is to create a disk image, and try to recovery files from it.
O is immediately beeing replaced by 1. With the up- and down-arrows, O is not even suggested (using R-Studio for Linux 3.9)....
Regards, Moses
Re: "Skip Files with bad sectors"
Thank you very much for this helpful feedback! Great tool!Data-Medics wrote:It's usually best to clone the disk that has the bad sectors first using a tool like ddrescue in linux. Unfortunately any tool that runs in Windows will have limitations with handling bad sectors, it's just a Windows factor. Then run R-Studio against the clone and you're good to go.
Moses
PS
By the way: I tried the latest Windows-version of R-Studio: It's not possible as well to set the "Default read attempt to 0".
Is this possible or am I doing something wrong??
Re: "Skip Files with bad sectors"
Thank you very much for this helpful feedback! Great tool!Data-Medics wrote:It's usually best to clone the disk that has the bad sectors first using a tool like ddrescue in linux. Unfortunately any tool that runs in Windows will have limitations with handling bad sectors, it's just a Windows factor. Then run R-Studio against the clone and you're good to go.
Moses
PS
By the way: I tried the latest Windows-version of R-Studio: It's not possible as well to set the "Default read attempt to 0".
Is this possible or am I doing something wrong??
Re: "Skip Files with bad sectors"
If you read a sector 0 times, you are not reading it at all.moses wrote:PS
By the way: I tried the latest Windows-version of R-Studio: It's not possible as well to set the "Default read attempt to 0".
Is this possible or am I doing something wrong??
-
- Posts: 220
- Joined: Tue Oct 20, 2015 10:13 am
- Location: Providence, RI USA
- Contact:
Re: "Skip Files with bad sectors"
HAHA, took the words right out of my mouth.RForce wrote:If you read a sector 0 times, you are not reading it at all.moses wrote:PS
By the way: I tried the latest Windows-version of R-Studio: It's not possible as well to set the "Default read attempt to 0".
Is this possible or am I doing something wrong??